Gtco DrawingSlate I & II Commands Manual de usuario descargar pdf

Power Up Default

Format #23

Run mode

9600 8 none 1

1000 lines per inch and 125 point per second

Operating Modes

Run Mode: Digitizer outputs coordinate data continuously.

Track Mode: Digitizer outputs coordinate data when button is down.

Line Mode: Digitizer outputs coordinate data points when a button is down; plus one when

the button is released.

Point Mode: One point is sent when a button is pressed.

Increment Mode Filter: Puts a movement filter on data in any mode. The transducer must

move N counts before the data can be sent. Then both axis data are updated. If out of

proximity data is enabled in increment mode, two data point may be sent on leaving

proximity.

Grid Update Mode Filter: Similar to Increment Mode Filter, except only the axis that the inc

occurred in is updated; the other axis is its old value.

Prompt Mode Modifier: Places the additional restriction on data transmission that the host

must transmit a prompt character to the tablet for each data point output. All other rules

of normal operation apply. The prompt character is “?”. Prompting is a feature, which

operates in conjunction with any of the above standard modes.

Send Data Out of Proximity Mode Modifier: If this flag is set, coordinate data will be sent

when it meets the output conditions in or out of the active area. Cordless units may not

respond to button information until cursor is close to tablet.

NOTE: This command should be sent after the mode commands.

1 2 3 4 5 6 ... 11 12

Indice de contenidos

Pagina 1

Power Up Default Format #23 Run mode 9600 8 none 1 1000 lines per inch and 125 point per second Operating Modes Run Mode: Digitizer outputs coord

Pagina 2

Pagina 3 - ASCII Formats

CTS CTS will stop next data byte out if bit in menu is enabled. CTS toggled in software setup mode, will send a “T” at *. DTR DTR toggled hig

Pagina 4

“(01CAL0001\\TABLET\\CalComp DrawingSlate 4x5 xx) cr if” or similar. See plug and play spec for more information. Binary Formats 20 Format AFT 4

Pagina 5

Send Data in Margin: If this flag is set, coordinate data point will be sent when it meets the output conditions in the active area or when in mar

Pagina 6 - Cursor Coding

ASCII Formats 31090, 31120 or 31180 with Resolution <510 LPI 0 XXXX YYYY C CR [LF] 3 XXXX YYYY C CR [LF] 3 DELTA +XXXX +YYYY C CR [LF] 15

Pagina 7 - Commands (RS-232)

Added in Mod 4 (Firmware 70181) to Support Pressure Pen in Summa Mode 3 15 8 X…X, Y…Y, PPPPP, C CR [LF] +X…X, Y…Y, PPPPP, CACB, TO, CR, [LF] +X….X,

Pagina 8

23 Format (2G) from 0 to 1 FH (0 to 31) Only If Pressure Pen Data is Enabled 7 6 5 4 3 2 1 0 1 1 P4 P3 P2 P1 P0 X15 X14 PRESSURE 0 TO 31 2 0 X13

Pagina 9

31 Format 7 6 5 4 3 2 1 0 1 0 1 0 0 T2 T1 T0 PR PR 0 = IN PROX 1 = OUT OF PROX 2 0 0 0 C4 C3 C2 C1 C0 t2, 1, and 0 = 100 or 000 (lectra) 3 0 0 X5

Pagina 10

0+3 1+3 0+1+3 2+3 0+2+3 1+2+3 0+1+2+3 9 : ; < = > ? 01001 01010 01011 01100 01101 01110 01111 00001 00010 00001 00011 00001 00010 00001 5 6 7

Pagina 11

Tablet can respond to 2x00 commands in the 2000/9100 subsets. 2000 Commands (2x00) NOTE: Use commands below only when in 2000 mode/formats. Can

Pagina 12 - Binary Formats

0 @ B E G h Q R S T TABLET BIT TO 0 RUN MODE POINT MODE SET DELTA MODE AXIS UPDATE bin ASCII 140 100 DATA RATE 75 50 25 20 7 7 1 A D I h

Comentarios a estos manuales

Sin comentarios

Gtco DrawingSlate I & II Commands Manual de usuario

Busca en linea o descarga Manual de usuario para Hardware De La Computadora Gtco DrawingSlate I & II Commands. GTCO DrawingSlate I & II Commands User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Hardware De La Computadora Gtco DrawingSlate I & II Commands