Gtco 2500 Series - Users Guide 1/3 Manual de usuario

2500 Series 1 Table of Contents Introduction Installation Switches and Indicators Setting the Soft Switches Selected Applications So

2500 Series 10 Switches and Indicators The Tablet-Status Display blocks across the top of the tablet have multiple functions. In operat

2500 Series 11 Handshake Lights when host generated handshaking prevents tablet transmission. Disable Lights when tablet is in HALT mode, X-OFF h

2500 Series 12 Setting the Soft Switches During installation, the numbered display blocks act as switches that must be set to select operating para

2500 Series 13 5. Repeat steps 1 through 4, selecting new banks and setting the switches until all the necessary switches have been set. Rememb

2500 Series 14 NOTE: If frequent changing of soft switch settings is required, one set of parameters may be saved in memory and recalled whenever t

2500 Series 15 AUTOCAD WITH CALCOMP 2000 EMULATION AUTOCAD WITH SUMMAGRAPHICS BIT PAD ONE EMULATION SWITCH 1 2 3 4 5 6 7 8 BANK #1 0 0 0 0 0 0 0 1

2500 Series 16 AUTOCAD WITH HITACHI TIGER HDG-1111 EMULATION SWITCH 1 2 3 4 5 6 7 8 BANK #1 0 0 0 0 0 0 0 1 BANK #2 0 1 0 0 1 1 0 0 BANK #3 0 1 1 0

2500 Series 17 CAD KEY WITH SUMMA BIT PAD ONE EMULATION SWITCH 1 2 3 4 5 6 7 8 BANK #1 0 0 0 0 0 0 0 1 BANK #2 0 1 0 0 0 0 0 0 BANK #3 0 0 0 1 1 1

2500 Series 18 POINT LINE WITH CALCOMP 2000 EMULATION SWITCH 1 2 3 4 5 6 7 8 BANK #1 0 0 0 0 0 0 0 1 BANK #2 0 1 0 0 0 0 0 0 BANK #3 0 0 0 1 1 1 0

2500 Series 19 NOTES: Most software for personal computers will work with the tablet provided that the transmit and receive lines are correct. Com

2500 Series 2 WARNING This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordanc

2500 Series 20 Switch Controlled Parameters The following operating characteristics are controlled by the settings of the soft switch banks. The s

2500 Series 21 BANK FIVE Communications DTE or DCE, handshake and echo. X-ON/X-OFF Enable or disable output. Tablet begins transmitting at power o

2500 Series 22 SWITCH 4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 5 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 6 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 7 0 0 1 1 0 0 1 1

2500 Series 23 SWITCH 2 0 0 0 0 0 0 0 0 1 1 1 1 3 0 0 0 0 1 1 1 1 0 0 0 0 4 0 0 1 1 0 0 1 1 0 0 1 1 5 0 1 0 1 0 1 0 1 0 1 0 1 DATA RATE (POINTS

2500 Series 24 Bank 3 Output SWITCH 1 0 0 0 0 1 1 1 1 2 0 0 1 1 0 0 1 1 3 0 1 0 1 0 1 0 1 RESOLUTION 200 LPI (LINES/INCH) 400 LPI 500 LPI 1000 LPI

2500 Series 25 SWITCH 4 1 5 0 6 0 7 0 8 1 RESERVED FORMATS 17

2500 Series 26 SWITCH 6 0 0 0 0 1 7 0 0 1 1 X 8 0 1 0 1 X PARITY ODD EVEN MARK SPACE DISABLED Bank 5 Special Functions SWITCH 1 0 1 ECHO DISABLED

2500 Series 27 SWITCH 8 0 1 9100 SERIES COMMANDS ENABLED DISABLED NOTE: Bank 2 switch 1 must be enabled before this switch bank may be used to sel

2500 Series 28 Corporate Headquarters 14557 N. 82nd Street Scottsdale, Arizona 85260 Tel: 1-866-746-3015 Support: 1-866-746-3015 Fax: 480-998-1

2500 Series 3 WARRANTY Seller makes no warranties except as set forth herein. Seller warrants that articles furnished hereunder are free from defe

2500 Series 4

2500 Series 5 Introduction The CalComp 2500 Tablet, when used with the appropriate host computer and software, is a means of entering information i

2500 Series 6 Warnings, Cautions and Notes Warnings: Indicates conditions, practices or procedures which must be followed to avoid injury or loss o

2500 Series 7 Installation Before beginning the installation, check the voltage indicator pin at the rear of the tablet to ensure that the voltage

2500 Series 8 3. Attach the other end of the RS-232C cable to the host’s communications port. 4. Connect the tablet’s power cable to the tabl

2500 Series 9 NOTE: Damage to the host may result if the tablet is operated with the AC line cord connected and the W3 jumper install